Miller Electric OM-4409 User Manual Page 53
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
OM-4409 Page 49
9-7. Servicing Engine Fuel And Lubrication Systems
803 228
! Stop engine and let cool.
! After servicing, start engine and
check for fuel leaks. Stop engine,
tighten connections as necessary,
and wipe up spilled fuel.
1 Oil Filter
2 Oil Drain Hose And Valve
3 Oil Fill Cap
4 Primary Fuel Filter (Fuel/Water
Separator)
5 Petcock
6 Secondary Fuel Filter
7 Fuel Tank Sludge Drain Valve
To change oil and filter:
The engine oil drain and compressor oil
drain hoses are located together in the
base. Be sure to select the correct hose
when draining engine oil.
Route engine oil drain hose through hole in
base. See engine manual and engine main-
tenance label for oil specifications.
To drain water from fuel system:
Open primary fuel filter petcock and drain
water into metal container. Close petcock
when water-free fuel flows.
To replace primary fuel filter:
Turn filter counterclockwise. Remove filter.
Apply thin coat of fuel to gasket on new filter.
Fill filter with fuel. Install filter and turn clock-
wise until tight. Bleed air from fuel system
according to engine manual.
Inspect fuel lines, and replace if cracked or
worn.
To replace secondary fuel filter:
See engine manual.
Close doors.
To drain sludge from fuel tank:
! Beware of fire. Do not smoke and
keep sparks and flames away from
drained fuel. Dispose of drained fuel
in an environmentally-safe manner.
Do not leave unit unattended while
draining fuel tank.
! Properly lift unit and secure in a level
position. Use adequate blocks or
stands to support unit while drain-
ing fuel tank.
Attach 1/2 ID hose to drain valve. Put metal
container under drain, and use screwdriver
to open sludge drain valve. Close valve
when sludge has drained. Remove hose.
4
5
Tools Needed:
3
7
Right Side
1
6
2
- Big Blue Air Pak 1
- From Miller to You 2
- TABLE OF CONTENTS 3
- 1-1. Symbol Usage 5
- 1-2. Arc Welding Hazards 5
- Medical Devices 6
- 1-3. Engine Hazards 7
- 1-4. Compressed Air Hazards 7
- 1-8. EMF Information 9
- UTILISATION 10
- LE CARBURANT MOTEUR peut prov 12
- 2-8. Information EMF 15
- SECTION 3 − DEFINITIONS 16
- SECTION 4 − SPECIFICATIONS 17
- Work like a Pro! 18
- C. MIG Mode 19
- A. DC Stick Mode 19
- B. AC Stick Mode (Optional) 19
- 4-6. TIG Volt-Ampere Curves 20
- 4-7. Fuel Consumption 21
- AC AMPERES 23
- OM-4409 Page 21 25
- SECTION 5 − INSTALLATION 26
- ! Do not weld on base. Weld 27
- ! Do not mount unit by sup 27
- ! Do not use flexible mounts 27
- Be sure to tighten rain cap 28
- Over 80,000 trained 30
- Start Your Professional 30
- Welding Career Now! 30
- ! Stop engine 32
- ! Turn off power before 33
- ! Do not use worn, dam 33
- 803 229 / 217 356-A 36
- 6-3. Process/Contactor Switch 38
- Generator power is not af 40
- ! Close panel opening 41
- ! Close panel 41
- 8-1. Battery Charge Controls 43
- 8-5. Jump Starting Procedure 46
- 9-1. Engine Maintenance Label 47
- Ref. 206 467 49
- ! Stop engine and let cool 51
- 9-6. Adjusting Engine Speed 52
- OM-4409 Page 51 55
- SECTION 11 − TROUBLESHOOTING 61
- B. Standard Generator Power 62
- C. Optional AC Power Plant 62
- D. Engine 63
- E. Air Compressor 64
- F. Optional Battery Charging 64
- OM-4409 Page 61 65
- SECTION 13 − CIRCUIT DIAGRAM 66
- OM-4409 Page 63 67
- SECTION 14 − RUN-IN PROCEDURE 68
- ! Do not touch hot exhaust 69
- ! Keep exhaust and pipe away 69
- Gauge Pressure (psi) 71
- 70-90 P.S.I.G 72
- 16-1. Selecting Equipment 73
- Electrically bond generator 73
- ! Ground generator to system 74
- ! Also see AWS Safety & 74
- Ref. ST-800 396-A / S-0625 77
- Customer-supplied equipment 78
- FOR DC OR AC WELDING 80
- 18-1. Positioning The Torch 81
- ST-162 002-B 82
- ST-162 003 / S-0792 83
- SECTION 19 − PARTS LIST 84
- OM-4409 Page 82 86
- OM-4409 Page 83 87
- OM-4409 Page 84 88
- OM-4409 Page 85 89
- 803 325-D 90
- OM-4409 Page 87 91
- Hardware is common and 92
- OM-4409 Page 89 93
- OM-4409 Page 90 94
- OM-4409 Page 92 96
- OM-4409 Page 95 99
- OM-4409 Page 96 100
- Effective January 1, 2007 101
- For Service 102
- Owner’s Record 102
Related products and manuals for Welding System Miller Electric OM-4409
(36 pages)© 2020, manymanuals.com. All rights reserved. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals