Miller Electric 230Volt Owner's Manual download pdf (Page 6)

OM-263 001 Page 2

FALLING EQUIPMENT can injure.

 Use equipment of adequate capacity to lift and

support unit.

 If using lift forks to move unit, be sure forks are

long enough to extend beyond opposite side of

unit.

 Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

 Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94−110) when manu-

ally lifting heavy parts or equipment.

MOVING PARTS can injure.

 Keep away from moving parts such as fans.

 Keep all doors, panels, covers, and guards

closed and securely in place.

 Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

 Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

FIRE OR EXPLOSION hazard.

 Do not install or place unit on, over, or near

combustible surfaces.

 Do not install unit near flammables.

 Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

READ INSTRUCTIONS.

 Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

 Use only genuine replacement parts from the manufacturer.

 Perform maintenance and service according to the Owner’s

Manuals, industry standards, and national, state, and local

codes.

1-3. Arc Welding And Plasma Cutting Hazards

Touching live electrical parts can cause fatal shock

or severe burns. The electrode and work circuit i

electrically live whenever the output is on. The inpu

power circuit and machine internal circuits are als

live when power is on. In semiautomatic or automati

wire welding, the wire, wire reel, drive roll housing

and all metal parts touching the welding wire ar

electrically live. Incorrectly installed or improperl

grounded equipment is a hazard.

 Do not touch live electrical parts.

ELECTRIC SHOCK can kill.

 Wear dry, hole-free insulating gloves and body protection.

 Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

 Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

 Use AC output ONLY if required for the welding or cutting process.

 If AC output is required, use remote output control if present on

unit.

 Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

 Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

 Properly install, ground, and operate this equipment according to

its Owner’s Manual and national, state, and local codes.

 Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

 When making input connections, attach proper grounding conduc-

tor first − double-check connections.

 Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

 Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

 Turn off all equipment when not in use.

 Do not use worn, damaged, undersized, or poorly spliced cables.

 Do not drape cables over your body.

 If earth grounding of the workpiece is required, ground it directly

with a separate cable.

 Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

 Do not touch electrode holders connected to two welding ma-

chines at the same time since double open-circuit voltage will be

present.

 Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

 Wear a safety harness if working above floor level.

 Keep all panels and covers securely in place.

 Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

 Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

 Do not connect more than one electrode or work cable to any

single weld output terminal. Disconnect cable for process not in

use.

SIGNIFICANT DC VOLTAGE exists in inverter pow-

er sources AFTER removal of input power.

 Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section

before touching any parts.

HOT PARTS can burn.

 Do not touch hot parts bare handed.

 Allow cooling period before working on equip-

ment.

 To handle hot parts, use proper tools and/or

wear heavy, insulated welding gloves and

clothing to prevent burns.

1 2 3 4 5 6 7 ... 106

Comments to this Manuals

No comments

Miller Electric 230Volt Owner's Manual Page 6

Comments to this Manuals

Related products and manuals for Welding System Miller Electric 230Volt