®Auto-Darkening HelmetsModel: CoolBandtIntegratedHeadgear Cooling SystemOM-235 369A2009−11To help us serve you better, go to www.MillerWelds.Com/Helme
OM-235 369 Page 83-3. Installing Head ShroudAfter installing shroud,. make sure there are nogaps between shroud andhelmet edge.1 Head Shroud2 Magnetic
OM-235 369 Page 93-4. Charging The BatteryCharge battery only. with supplied chargerin an open, well−ven-tilated location.Do not allow battery. to get
OM-235 369 Page 103-5. Installing The BatteryDo not allow battery to get. wet. Do not attempt to openthe battery case.Keep battery away from. fire or
OM-235 369 Page 113-7. Removing Air Deflector To Adjust Air Flow1 Air Deflector2 ManifoldTo adjust air flow in helmet, re-move air deflector from mani
OM-235 369 Page 123-8. Operating The Controls123Read and follow these. instructions and thesafety labels carefully.This product is in-tended for use a
OM-235 369 Page 133-9. Checking The Helmet Cooling System Before UseRead and follow these in-. structions and the safetylabels carefully. Thisproduct
OM-235 369 Page 143-10. Operating Helmet Cooling System On 120 Volt AC Power11 Auxiliary Power JackTo operate helmet coolingsystem on AC (utility)pow
OM-235 369 Page 15SECTION 4 − MAINTENANCE4-1. Adjusting Headgear. There are four headgear adjust-ments: headgear top, tightness,angle adjustment, and
OM-235 369 Page 164-2. Replacing Fabric Headband1 Manifold2 Manifold Bracket3 Fabric HeadbandSlide manifold up and away frommanifold bracket. Push bra
OM-235 369 Page 174-3. Maintenance And StorageReplace damaged or dirty filter. Do not wash filter, clean with compressed air, or reusedirty filter.Ne
TABLE OF CONTENTSSECTION 1 − HELMET COOLER SAFETY PRECAUTIONS − READ BEFORE USING 1. . . . . . 1-1. Symbol Usage 1. . . . . . . . . . . . . . . . . .
OM-235 369 Page 18Battery run time is tooshort.Replace battery.Check filter and replace if necessary (see Section 3-6). A cloggedfilter element reduce
OM-235 369 Page 19SECTION 5 − PARTS LIST1210467853911Figure 5-1. CoolBand Helmet Cooling SystemDescriptionPartNo.ItemNo. QuantityFigure 5-1. CoolBand
OM-235 369 Page 20SECTION 6 − LIMITED WARRANTYLIMITED WARRANTY – Subject to the terms and conditions below. MillerElectric Mfg. Co., Appleton, Wiscons
ORIGINAL INSTRUCTIONS © 2009 Miller Electric Mfg. Co.Visit our website atwww.MillerWelds.com®Miller Electric Mfg. Co.An Illinois Tool Works Company163
OM-235 369 Page 1SECTION 1 − HELMET COOLER SAFETY PRECAUTIONS −READ BEFORE USINGProtect yourself and others from injury — read and follow these precau
OM-235 369 Page 2D Before each use, inspect the equipment for damage and verify it operates properly.D Dangerous contaminants may not smell or be visi
OM-235 369 Page 3SECTION 2 − BATTERY SAFETY PRECAUTIONS −READ BEFORE USINGProtect yourself and others from injury — read and follow these precautions.
OM-235 369 Page 4BATTERY ACID can BURN SKIN and EYES.D Replace damaged battery.D Do not touch materials from inside a damaged battery.D Flush eyes and
OM-235 369 Page 5SECTION 3 − HEADGEAR COOLING SYSTEMRead and follow these instructions and the safety labels carefully. This product is in-tended for
OM-235 369 Page 63-1. Helmet Cooling System SpecificationsApplication Fits Most Miller Welding HelmetsWeight Total Weight With Battery: 17.6 oz. (500
OM-235 369 Page 73-2. Installing Headgear1 Distance Adjustment Knob2O−Ring3 WasherRemove knobs, o−rings, and wash-ers from helmet headgear. Removehe
Comments to this Manuals