Miller Electric ICE-27C Owner's Manual

ProcessesDescriptionAir Plasma Cuttingand GougingAir Plasma CutterOM-2229 200 879KNovember 2003Visit our website atwww.MillerWelds.comSpectrum 375And

OM-2229 Page 6Revenez à la table des matièresD Isoler la pince de masse quand pas mis à la pièce pour éviter lecontact avec tout objet métallique.Il y

OM-2229 Page 7Revenez à la table des matièresLes bouteilles de gaz contiennent du gaz sous hautepression. Si une bouteille est endommagée, elle peutex

OM-2229 Page 8Revenez à la table des matières2-4. Principales normes de sécuritéSafety in Welding and Cutting, norme ANSI Z49.1, de l’American Wel-din

OM-2229 Page 9Return To Table Of ContentsSECTION 3 − DEFINITIONS3-1. Warning Label DefinitionsWarning! Watch Out! There arepossible hazards as shown b

OM-2229 Page 10Return To Table Of Contents3-2. Manufacturer’s Rating Label For CE Products203 892-AU0U2I2X@40°CSSERIAL NO.STOCK NO.H zpf =S1 U1=U1=I1

OM-2229 Page 11Return To Table Of ContentsSECTION 4 − INSTALLATION4-1. SpecificationsIf the unit is operated from a 30* ampere, 115 volt circuit or a

OM-2229 Page 12Return To Table Of Contents4-3. Duty Cycle And OverheatingDuty Cycle is percentage of 10 min-utes that unit can cut at rated loadwithou

OM-2229 Page 13Return To Table Of Contents16 in(406 mm)4-5. Selecting A Locationloc_2 3/96 - Ref. 802 784-B / 802 785-A / 802 786-B / 209 098 / 203 89

OM-2229 Page 14Return To Table Of Contents4-6. Connecting Gas/Air Supply802 787-B / Ref. 801 319-C / Ref. 802 784-B. Use only clean, dry air with 70to

OM-2229 Page 15Return To Table Of Contents4-7. Connecting Work Clamp802 463-A1 Work Clamp2 WorkpieceConnect work clamp to a clean,paint-free location

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-2229 Page 16Return To Table Of Contents4-9. Installing Alternative Plug1 Supplied 115 VAC PlugCut cord close to plug.2 Alternative Plug (230 VACPlu

OM-2229 Page 17Return To Table Of ContentsSECTION 5 − OPERATION5-1. Controls14235ONOFFPRESSURE60 PSI5624276Set To60 PSI (414 kPa)201624272016124272016

OM-2229 Page 18Return To Table Of Contents5-2. Cutting SpeedThe cutting speed curves show therecommended maximum cuttingspeed capabilities of the powe

OM-2229 Page 19Return To Table Of Contentsout bottom of cut.Ref. 802 8785-4. Sequence Of OperationAfter cutting arc starts, slowlystart moving torch a

OM-2229 Page 20Return To Table Of ContentsSECTION 6 − MAINTENANCE & TROUBLESHOOTING6-1. Routine MaintenanceY Disconnect power before maintaining..

OM-2229 Page 21Return To Table Of Contents6-2. Overload Protection: Trouble Lights & Checking Shield Cup Shutdown SystemIf certain problems occur,

OM-2229 Page 22Return To Table Of Contents6-3. Torch And Work Cable ConnectionsIf torch or work cable needs to beremoved or replaced, proceed asfollow

OM-2229 Page 23Return To Table Of Contents6-4. Checking/Replacing Retaining Cup, Tip, And ElectrodeOvertightening will strip threads. Do not overtight

OM-2229 Page 24Return To Table Of Contents6-5. Troubleshooting Power SourceConnect unit to proper inputvoltage (see Section 4-8).YesNoIs input powerco

OM-2229 Page 25Return To Table Of Contents6-6. Troubleshooting TorchTorch travel speed too slow;increase travel speed (seeSection 5-2). Clean orreplac

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol

OM-2229 Page 26Return To Table Of ContentsSECTION 7 − ELECTRICAL DIAGRAM200 809-DFigure 7-1. Circuit Diagram

OM-2229 Page 27Return To Table Of ContentsNotes

OM-2229 Page 28Return To Table Of ContentsSECTION 8 − PARTS LIST. Hardware is common andnot available unless listed.802 805-B3456789101112131415161718

OM-2229 Page 29Return To Table Of ContentsDescriptionPartNo.ItemNo.Figure 8-1. Main AssemblyQuantityDia.Mkgs.212 476 COVER ASSY (non-CE) (including) 1

OM-2229 Page 30Return To Table Of Contents1 183 427 Handle Assy, complete (1)2 171 248 Push Button Switch (1)3 203 120 Leads, 20ft (1)4 203 119 Main B

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 8/03Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA  2003 Miller Electric Mfg. Co. 1/03Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 US

dec_con1_11/02Return To Table Of ContentsDeclaration of Conformity forEuropean Community (CE) ProductsThis information is provided for units with CE c

OM-2229 Page 1Return To Table Of ContentsSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGpom _nd_8/031-1. Symbol UsageMeans Warning! Watch Out! The

OM-2229 Page 2Return To Table Of ContentsD On inverter power sources, failed parts can ex-plode or cause other parts to explode whenpower is applied.

OM-2229 Page 3Return To Table Of Contents1-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can cause severe burns.D Do not

OM-2229 Page 4Return To Table Of Contents1-5. Principal Safety StandardsSafety in Welding and Cutting, ANSI Standard Z49.1, from AmericanWelding Socie

OM-2229 Page 5Revenez à la table des matièresSECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATIONpom_fre 8/032-1. Signification des symbolesSig