Miller Electric OM-2219 Owner's Manual

Visit our website atwww.MillerWelds.comOM-2219 188 036GOctober 1999ProcessesProcessesDescriptionAir Plasma Cuttingand GougingAir Plasma CutterSpectrum

OM-2219 Page 6D N’approchez pas le tube du chalumeau et l’arc pilote lorsque la gâchette estenfoncée.D Le câble de masse doit être pincé correctement

OM-2219 Page 71-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenanceDES PIECES CHAUDES peuvent pro-voquer d

OM-2219 Page 81-4. Principales normes de sécuritéSafety in Welding and Cutting, norme ANSI Z49.1, de l’American Wel-ding Society, 550 N.W. Lejeune Rd,

OM-2219 Page 9SECTION 2 – INSTALLATION2-1. SpecificationsRated Cutting Maximum Open-Type of Output Plasma Gas Rated OutputRated CuttingCapacityMaximum

OM-2219 Page 102-4. Selecting A Locationloc_2 3/96 - ST-801 9761 Lifting HandlesUse handles to lift unit.2 Hand CartUse cart or similar device to move

OM-2219 Page 112-5. Connecting Work Clamp And Gas/Air SupplyRef. 801 977-A1 Work Clamp2 WorkpieceWork clamp cable is attached tofront of unit. Connect

OM-2219 Page 12SECTION 3 – OPERATIONIf the welding generator includes a fine adjust control, be sure to set thecontrol to maximum for full output cont

OM-2219 Page 131 Output Control2 Power SwitchPlace controls as indicated above. Only gas/air circuit is activated when the Power switchis turned On wi

OM-2219 Page 143-3. Sequence Of OperationPut On PersonalSafetyEquipmentAfter cutting arc starts, slowlystart moving torch across metal.Adjust torch sp

OM-2219 Page 15SECTION 4 – MAINTENANCE & TROUBLESHOOTING4-1. Routine MaintenanceY Disconnect power before maintaining.. Maintain more oftenduring

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-2219 Page 164-2. Ground Fault Circuit Interrupter (GFCI)Ref. 801 977-A / Ref. 802 180-A1 Ground Fault CircuitInterrupter GFCI2 Spring-Loaded Door (

OM-2219 Page 174-3. Trouble Lights1 Pressure LightLights if gas/air pressure is below40 PSI (276 kPa).Turn power Off, and check for prop-er gas/air pr

OM-2219 Page 18Trouble RemedyNo cutting output; Power light off;Trouble lights off; Ready light off; fan mo-tor FM does not run.Place Power switch in

OM-2219 Page 19SECTION 5 – ELECTRICAL DIAGRAM193 622Figure 5-1. Circuit Diagram

OM-2219 Page 20SECTION 6 – PARTS LIST. Hardware is common andnot available unless listed.802 180-C1234678911121314151617182021222324252627282930313233

OM-2219 Page 21DescriptionPartNo.Dia.Mkgs.ItemNo.Figure 6-1. Complete AssemblyQuantity1 187 782 WRAPPER 1. . . . . . . . . . . . . . . . . . . . . .

OM-2219 Page 22DescriptionPartNo.Dia.Mkgs.ItemNo.Figure 6-1. Complete Assembly (continued)Quantity51 138 442 LABEL, caution falling equipment 2. . .

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 7/00Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA  2000 Miller Electric Mfg. Co. 6/00Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 US

TABLE OF CONTENTSSECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1. . . .

OM-2219 Page 1SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USINGpom _nd_9/981-1. Symbol UsageMeans Warning! Watch Out! There are possible hazardswith

OM-2219 Page 2D On inverter power sources, failed parts can ex-plode or cause other parts to explode whenpower is applied. Always wear a face shieldan

OM-2219 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can cause severe burns.D Do not touch hot parts bare hande

OM-2219 Page 41-4. Principal Safety StandardsSafety in Welding and Cutting, ANSI Standard Z49.1, from AmericanWelding Society, 550 N.W. LeJeune Rd, Mi

OM-2219 Page 5SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT UTILISATIONpom_nd_fre_5/971-1. Signification des symbolesSignifie Mise en garde ! Soyez