Miller Electric SWLL-115 Owner's Manual

AMD-4, AMD-4G, AMD-4GR,AMD−4GH, AMD-115G,AMD-115GR, And AMD-115GHProcessesDescriptionWire FeederAutomatic WeldingOM-179 082F 2010−08Visit our website

OM-179 082 Page 6Il reste une TENSION DC NON NÉGLIGEABLE dansles sources de soudage onduleur UNE FOISl’alimentation coupée.D Arrêter les convertisseur

OM-179 082 Page 7LES ACCUMULATIONS DE GAZrisquent de provoquer des blessuresou même la mort.D Fermer l’alimentation du gaz protecteur en casde non-uti

OM-179 082 Page 8Les PIÈCES MOBILES peuventcauser des blessures.D Ne pas s’approcher des organes mobiles.D Ne pas s’approcher des points de coincement

OM-179 082 Page 92-5. Principales normes de sécuritéSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,de Global Engineering Docume

OM-179 082 Page 10

OM-179 082 Page 11SECTION 3 − INSTALLATION3-1. SpecificationsModelWire Feed SpeedRangeWire DiameterRangeType Of InputPowerInput PowerCordWeightAMD-4,

OM-179 082 Page 123-3. Typical Equipment Location131 138-A1 Welding Power Source2 Gas Cylinder3 Side Beam4 Weld Control5 Spool Support6 Wire Drive Ass

OM-179 082 Page 133-5. Motor Mounting And Gun, Weld Cable, And Gas Connections802 869-B / Ref. 804 391-A / Ref. 801 443-D / Ref. 804 392-A. Drive moto

OM-179 082 Page 143-6. Plug ConnectionsRef. 801 440 / Ref. 801 443-D1 Weld Control2 Motor Control Cord (NotSupplied)Cord is available in 10 ft (3 m),3

OM-179 082 Page 15SECTION 4 − MAINTENANCE AND TROUBLESHOOTING4-1. Routine Maintenance! Disconnect power before maintaining.. Maintain more oftenduring

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-179 082 Page 164-3. TroubleshootingTrouble RemedyElectrode wire feeding stops or feeds er-ratically during welding.Readjust hub tension and drive r

OM-179 082 Page 17Figure 5-2. AMD-115G, AMD-115GR, And AMD-115GH207 239

OM-179 082 Page 18SECTION 6 − PARTS LIST801 456-GSee Section Table 6-1Drive Roll & Wire Guide Kits. Hardware is common andnot available unless lis

OM-179 082 Page 19Description QuantityPartNo.Dia.Mkgs.ItemNo.Figure 6-1. Drive Assembly, Wire10 M1,2 178 097 AMD−4GH MOTOR W/GAS VALVE&VOLT SENSE

OM-179 082 Page 20Table 6-1. Drive Roll And Wire Guide KitsWire SizeInletGuideInter-mediateGuideV-GROOVE U-GROOVE VK-GROOVE UC-GROOVEFraction Metric4

Notes

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 2010−01Your distributor also givesyou ...ServiceYou always get the

ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2010 Miller Electric Mfg. Co. 2010−01Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 ...1-1. Symbol Usage 1 ...

OM-179 082 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _2010−037Protect yourself and others from injury — read and follow these precau

OM-179 082 Page 2D Keep your head out of the fumes. Do not breathe the fumes.D If inside, ventilate the area and/or use local forced ventilation at th

OM-179 082 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over,

OM-179 082 Page 41-4. California Proposition 65 WarningsWelding or cutting equipment produces fumes or gaseswhich contain chemicals known to the State

OM-179 082 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATIONfre_som_2010−037Se protéger et protéger les autres contre le risque de bles