Miller Electric Weld Oscillator Owner's Manual

Visit our website atwww.MillerWelds.comWeld OscillatorProcessesDescriptionAutomatic Welding SystemAutomatic WeldingOM-1085 052 563EJanuary 1996

OM-1085 Page 6Le rayonnement de l’arc du procédé de soudagegénère des rayons visibles et invisibles intenses(ultraviolets et infrarouges) susceptibles

OM-1085 Page 71-3. Dangers supplémentaires en relation avec l’installation, le fonctionnementet la maintenanceRisque D’INCENDIE OUD’EXPLOSION.D Ne pas

OM-1085 Page 81-4. Principales normes de sécuritéSafety in Welding and Cutting, norme ANSI Z49.1, de l’American Wel-ding Society, 550 N.W. Lejeune Rd,

OM-1085 Page 9SECTION 2 − INSTALLATION2-1. SpecificationsInputSpeedDwellTotal SlideWidthCenterWeightInputPowerSpeedDwellTotal SlideTravelWidthCenterAd

OM-1085 Page 102-4. Oscillator Control DimensionsDimensionsABA 11-1/4 in (285 mm)B 11-1/4 in (285 mm)CC 9-1/2 in (241 mm)CDD 3/4 in (19 mm)DE 9-1/2 in

OM-1085 Page 112-6. Installation Of Customer-Supplied Remote ControlsST-052 705-ARemove oscillator control wrapper.Loosen strain relief on lower right

OM-1085 Page 12A. Remote Start/Stop SwitchFor the remote start/stop switch to work, the Mode switch must be in the RUNposition.NOTEConnect leads from

OM-1085 Page 13E. Remote Center Position ControlIf multiple Center Position remote controls are desired, they must be switchedusing relays with gold a

OM-1085 Page 142-7. Interconnecting, Oscillator Control, and Power Cord ConnectionsST-052 310-A1 Oscillator Control2 Oscillating Slider Assembly3 Inte

OM-1085 Page 15SECTION 3 − OPERATION3-1. ControlsST-052 315-A1 Power Switch And Pilot LightUse Power switch to turn unit and pilot lightOn and Off.2 M

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-1085 Page 16SECTION 4 − MAINTENANCE4-1. Routine MaintenanceY Disconnect power before maintaining.Every MonthBlow Off NeopreneSeals On Slide.3 Month

OM-1085 Page 174-3. Slide LubricationST-154 580Y Turn Off and unplug unit.1 Gun Mounting Plate2 Slide Cover With Seal3 Shaft4 Screw Lead5 Pillow Block

OM-1085 Page 184-5. Slide Potentiometer Replacement1 Potentiometer GearLoosen setscrews, and removegear from potentiometer shaft.2 Mounting Plate Scre

OM-1085 Page 19SECTION 5 − ELECTRICAL DIAGRAMFigure 5-1. Circuit DiagramSC-099 133-B

OM-1085 Page 20Notes

OM-1085 Page 21SECTION 6 − PARTS LIST1245Fig 6-3Fig 6-23ST-052 310-A. Hardware is common andnot available unless listed.Figure 6-1. Main AssemblyDescr

OM-1085 Page 2212345 6789101112131415161718191720212223242526272829303132343535363734335ST-052 312-C. Hardware is common andnot available unless liste

OM-1085 Page 23DescriptionPartNo.Dia.Mkgs.009 286ItemNo.Figure 6-2. Slide, Oscillator (Fig 6-1 Item 1)Quantity1 009 278 FOOT, closer seal 4. . . . .

OM-1085 Page 241234567891011 1213 14 151617181912021222324 2526272829303132333435363734440393841ST-052 311-A. Hardware is common andnot available unle

OM-1085 Page 25DescriptionPartNo.Dia.Mkgs.009 285ItemNo.Figure 6-3. Control Box (Fig 6-1 Item 3)Quantity1 R4,5 009 154 POTENTIOMETER, CP plain rnd 1/T

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1. . .

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.Effective January 1, 1997(Equipment with a serial number preface of “KH” or ne

PRINTED IN USA  1997 Miller Electric Mfg. Co.Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 USAInte

OM-1085 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _nd_5/971-1. Symbol UsageMeans Warning! Watch Out! There are possible hazardswith

OM-1085 Page 2Arc rays from the welding process produce intensevisible and invisible (ultraviolet and infrared) raysthat can burn eyes and skin. Spark

OM-1085 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over, or

OM-1085 Page 41-5. EMF InformationConsiderations About Welding And The Effects Of Low FrequencyElectric And Magnetic FieldsWelding current, as it flow

OM-1085 Page 5SECTION 1 − CONSIGNES DE SECURITE − LIRE AVANTUTILISATIONsom _nd_fre 5/971-1. Signification des symbolesSignifie Mise en garde ! Soyez v