Miller Electric SuitCase 8VS User Manual

SuitCase 8VSOM-1599 200 624M2005−11ProcessesDescriptionMIG (GMAW) WeldingFlux Cored (FCAW) WeldingWire FeederFile: MIG (GMAW)Visit our website atwww.M

OM-1599 Page 6Le rayonnement de l’arc du procédé de soudagegénère des rayons visibles et invisibles intenses(ultraviolets et infrarouges) susceptibles

OM-1599 Page 72-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenanceRisque D’INCENDIE OU D’EXPLO-SION.D Ne

OM-1599 Page 82-5. Principales normes de sécuritéSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,de Global Engineering Documents

OM-1599 Page 9SECTION 3 − DEFINITIONS3-1. Warning Label Definitions1 1.1 1.2 1.33 3.1 3.2 3.34 4.1+22.12.2++56+2.3S-178 936Warning! Watch Out! There a

OM-1599 Page 103-2. Manufacturer’s Rating Label For CE ProductsST-181 678For label locationsee Section 5-1.S/N:HzIP 23VAX%VU1=A I1=U2=I2=1007.0DC100 5

OM-1599 Page 11SECTION 4 − INSTALLATION4-1. SpecificationsType ofInputPowerWeldingPowerSourceTypeWire FeedSpeedRangeWire TypeAndDiameterInputWeldingCi

OM-1599 Page 124-4. Installing And Aligning Wire Guide And Drive Rolls802 706-A / Ref. 132 808-F / Ref. 162 079-A / Ref. 180 967Installing Wire Guide

OM-1599 Page 134-5. Connecting Welding Gun And Voltage Sensing ClampRef. 802 706-A / 802 768-A / Ref. S-0621-CY Turn Off wire feeder andwelding power

OM-1599 Page 144-7. Connecting Weld CableRef. 132 808-F / Ref. 802 706Y Turn Off wire feeder andwelding power source. Stopengine on weldinggenerator.1

OM-1599 Page 15SECTION 5 − OPERATION5-1. Controls For Non-CE ModelsRef. 803 626-A / Ref. 802 706-A/ Ref. 803 1241 Power Control Switch2 Trigger Hold S

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-1599 Page 165-2. Controls For CE ModelsRef. 803 626-A / Ref. 802 706-A / Ref. 203 745 / Ref. 203 7491 Power Control Switch2 Trigger Hold SwitchDepr

OM-1599 Page 17SECTION 6 − MAINTENANCE & TROUBLESHOOTING6-1. Routine MaintenanceY Disconnect power before maintaining.. Maintain more oftenduring

OM-1599 Page 186-3. TroubleshootingTrouble RemedyWire does not feed; open-circuit voltageavailable.Check circuit breaker CB1. Reset CB1.Unit overheate

OM-1599 Page 19SECTION 7 − ELECTRICAL DIAGRAMS203 029−CFigure 7-1. Circuit Diagram For Wire Feeder

OM-1599 Page 20SECTION 8 − PARTS LIST. Hardware is common andnot available unless listed.Figure 8-1. Complete Assembly802 675-E12457859101112131415161

OM-1599 Page 21Figure 8-1. Complete AssemblyDescriptionQuantityPartNo.Dia.Mkgs.ItemNo.1 202 695 Nut, Hub 1. . . . . . . . . . . . . . . . . . . . .

OM-1599 Page 22Figure 8-1. Complete Assembly (Continued)DescriptionQuantityPartNo.Dia.Mkgs.ItemNo.37 081 895 Nut, 010−32 Rubber .75dia .81l Insert In

OM-1599 Page 23Figure 8-2. Drive Roll & Wire Guide Kits (2 Drive Roll)Base selection of drive rolls upon the following recommended usages:1. V-Gr

OM-1599 Page 24Notes

OM-1599 Page 25NotesOver 80,000 trainedsince 1930!400 Trade Square East, Troy, Ohio 453731-800-332-9448 www.welding.orgStart Your ProfessionalWelding

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbo

OM-1599 Page 26Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 1/05Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA © 2005 Miller Electric Mfg. Co. 10/05Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 U

dec_wire_6/05Declaration of Conformity forEuropean Community (CE) ProductsThis information is provided for units with CE certification (see rating lab

OM-1599 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _3/05Y Warning: Protect yourself and others from injury — read and follow these pr

OM-1599 Page 2Arc rays from the welding process produce intensevisible and invisible (ultraviolet and infrared) raysthat can burn eyes and skin. Spark

OM-1599 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over, or

OM-1599 Page 41-5. Principal Safety StandardsSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,from Global Engineering Documents (

OM-1599 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATIONsom _3/05Y Avertissement : se protéger et protéger les autres contre le risque