Miller-electric wire feeder User Manual

cover 1/94 – ST-108 014-A PRINTED IN USA 1995 MILLER Electric Mfg. Co.Read and follow these instructions and allsafety blocks carefully.Have only tra

OM-877 Page 65. ANSI Standard Z41.1, STANDARD FOR MEN’SSAFETY-TOE FOOTWEAR obtainable from theAmerican National Standards Institute, 1430Broadway, New

OM-877 Page 7SECTION 3 – SPECIFICATIONSRated Load For Single-PhaseAC Input 50/60 Hertz 100%Duty CycleWeightNet Ship10 kW At120 Volts, 83 Amperes240 Vo

OM-877 Page 8Table 4-1. Cord Size By Ampacity RatingCord Size–AWG* Ampacity Of Cord18 1014 1812 2510 308 406 504 702 95*Cord sizes are based on Nation

OM-877 Page 9SECTION 5 – OPERATOR CONTROLSST-108 014-ACord StorageAreaAmperage LoadSwitchesLoad SelectorSwitch120/240VACPilot Light For120VAC LoadAC V

OM-877 Page 10Table 5-1. Power Requirements For LoadAmperage At Input VoltageAMPERESAT 120VKW181.5122172.5213254335426507587.5628679751083AMPERESAT 24

OM-877 Page 113. Connect Load Bank cord to the ac power source.Be sure to use appropriate cord when Load Bankhas both 120 and 240 volt cords installed

OM-877 Page 12SECTION 8 – PARTS LISTFigure 8-1. Main AssemblyST-108 01612Fig 8-23Fig 8-34 567891011121314

OM-877 Page 13DescriptionPartNo.ItemNo.Figure 8-1. Main AssemblyQuantity1 106 661 PANEL, LH side 1. . . . . . . . . . . . . . . . . . . . . . . . .

OM-877 Page 14DescriptionPartNo.Dia.Mkgs.ItemNo.Figure 8-2. Panel, Front w/Components (Fig 1 Item 2)Quantity1 NAMEPLATE, (order by model and serial nu

OM-877 Page 15DescriptionPartNo.ItemNo.Figure 8-3. Resistor Assembly (Fig 1 Item 3)Quantity1 106 667 BUS BAR, connecting resistors 2. . . . . . . .

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-877 Page 16Notes

OM-877 Page 17Notes

OM-877 Page 18Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 7/00Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA  2000 Miller Electric Mfg. Co. 6/00Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 US

OM-877 – 11/95TABLE OF CONTENTSSECTION 1 – SAFETY RULES FOR OPERATION OF ARC WELDING POWER SOURCE 1. . . . . . . 1-1. Introduction 1. . . . . . . . .

OM-877 Page 1SECTION 1 – SAFETY RULES FOR OPERATION OF ARC WELDING POWER SOURCE1-1. INTRODUCTIONWe learn by experience. Learning safety through per-so

OM-877 Page 2atmosphere or where the radiant energy can penetrateto atmospheres containing even minute amounts oftrichloroethylene or perchloroethylen

OM-877 Page 3Locate or secure cylinders so they cannot be knockedover.Passageways and work areas. Keep cylinders clear ofareas where they may be struc

OM-877 Page 41-3. ARC WELDINGComply with precautions in 1-1, 1-2, and this section.Arc Welding, properly done, is a safe process, but acareless operat

OM-877 Page 5quate to carry ground currents safely. Equipment madeelectrically HOT by stray current may shock, possiblyfatally. Do NOT GROUND to elect