Miller-electric 852 User Manual

302, 452, 652 (60 Hz), 402, 602, 852 (50 Hz)ProcessesDescriptionTIG (GTAW) WeldingStick (SMAW) WeldingOM-222 164 850AD2007−03Air Carbon Arc (CAC-A)Cut

OM-222 Page 6Le rayonnement de l’arc génère des rayons visibles etinvisibles intenses (ultraviolets et infrarouges) suscep-tibles de causer des brûlur

OM-222 Page 72-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien del’appareil.Risque D’INCENDIE OU D’EXPLO-SIOND Ne pas

OM-222 Page 82-4. Principales normes de sécuritéSafety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1,de l’American Welding Society, 550

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 9SECTION 3 − DEFINITIONS3-1. General Precautionary LabelWarning! Watch Out! The

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 103-2. Input Connection Label1 Warning! Watch Out! Thereare possible hazards as

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 113-5. Manufacturer’s Rating Labels For CE Products. Match label to one on unit

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 123-6. Symbols And DefinitionsSome symbols are found only on CE products.NoteAA

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 13SECTION 4 − INSTALLATION4-1. SpecificationsModelRatedWeldingAmpRange DCMaximu

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 144-3. Volt-Ampere CurvesVolt-ampere curves show mini-mum and maximum voltage

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 154-4. Selecting A Location1 Lifting Eye2 Lifting ForksUse lifting eye or lifti

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 164-5. Dimensions And WeightsDimensions300 Amp Models 450 Amp Models 650 Amp Mo

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 174-6. TippingY Be careful when placing ormoving unit over unevensurfaces.4-7.

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 184-8. Weld Output Terminals And Selecting Cable SizesTotal Cable (Copper) Leng

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 194-10. Remote 14 Receptacle InformationSocket Information24 VOLTS ACA 24 volts

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 204-12. Electrical Service Guide60 Hertz Models 300 Amp Model 450 Amp Model 650

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 214-13. Placing Jumper LinksRef. ST-800 103-AY Disconnect and lockout/tag-out i

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 224-14. Connecting Input Power 800 103-C / Ref. 801 116-A3/8 in3/8 inTools Need

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 23SECTION 5 − OPERATION5-1. Controls (Non CE Models)1 Polarity Selector Switch

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 245-2. Controls (CE Models)1 Polarity Selector Switch (Optional On 50Hz Models)

. A complete Parts List is available at www.MillerWelds.comOM-222 Page 256-2. Fuse F1Ref. ST-800 101-CY Turn Off power before open-ing rear access doo

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbo

OM-222 Page 26SECTION 7 − ELECTRICAL DIAGRAMFigure 7-1. Circuit Diagram

OM-222 Page 27218 518-A

OM-222 Page 28SECTION 8 − PARTS LISTA complete Parts List is available on-line at www.MillerWelds.com.NOTEhttp://www.millerwelds.com/service/replaceme

Notes

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 2007−01Your distributor also givesyou ...ServiceYou always get the

PRINTED IN USA © 2007 Miller Electric Mfg. Co.2007−01Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914

dec_stat_6/05Declaration of Conformity forEuropean Community (CE) ProductsThis information is provided for units with CE certification (see rating lab

OM-222 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _3/05Y Warning: Protect yourself and others from injury — read and follow these pre

OM-222 Page 2Arc rays from the welding process produce intensevisible and invisible (ultraviolet and infrared) raysthat can burn eyes and skin. Sparks

OM-222 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over, or

OM-222 Page 41-5. Principal Safety StandardsSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,from Global Engineering Documents (p

OM-222 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANTUTILISATIONsom_fre 8/032-1. Signification des symbolesSignifie « Mise en garde. Faire pre