Miller Electric Ice-12C Torch Owner's Manual

Spectrum ThunderAnd Ice-12C TorchProcessesDescriptionRAir Plasma Cuttingand GougingAir Plasma CutterOM-194 473JApril 2003Visit our website atwww.Mille

OM-194 473 Page 6D N’approchez pas le tube du chalumeau et l’arc pilote lorsque la gâchette estenfoncée.D Le câble de masse doit être pincé correcteme

OM-194 473 Page 71-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenanceDES PIECES CHAUDES peuvent pro-voque

OM-194 473 Page 81-5. Information sur les champs électromagnétiquesDonnées sur le soudage électrique et sur les effets, pour l’organisme,des champs ma

OM-194 473 Page 9SECTION 2 – DEFINITIONS2-1. Warning Label DefinitionsWarning! Watch Out! There arepossible hazards as shown by thesymbols.1 Cutting s

OM-194 473 Page 102-2. Manufacturer’s Rating Label For CE Productsand CE markings only apply when the torch is used with shielded parts: retaining cup

OM-194 473 Page 11SECTION 3 – INSTALLATION3-1. Specifications For Non-CE Power SourcesPrimaryVoltsPrimaryAmperesPrimary Service(Recommended)SecondaryV

OM-194 473 Page 123-5. Torch Dimensions And WeightRef. 801 397-A3.0 lb (1.4 kg)1 in(25 mm)8-3/8 in(213 mm)1-3/8 in(35 mm)18 in(457 mm)3-6. Selecting

OM-194 473 Page 133-7. Connecting Work Clamp802 463-A1 Work Clamp2 WorkpieceConnect work clamp to a clean,paint-free location on workpiece, asclose to

OM-194 473 Page 14SECTION 4 – OPERATION4-1. Controls231OFFONPOWERCUPTEMPINPUT VOLTAGE1 Power Switch2 Power LightUse light to tell if unit is energized

OM-194 473 Page 154-3. Trigger Safety LockTrigger Locked Trigger Unlocked1 Trigger801 545-A1

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-194 473 Page 16out bottom of cut.801 400-A4-4. Sequence Of OperationAfter cutting arc starts, slowlystart moving torch across metal.Adjust torch sp

OM-194 473 Page 17SECTION 5 – MAINTENANCE & TROUBLESHOOTING5-1. Routine MaintenanceY Disconnect power before maintaining.. Maintain more oftenduri

OM-194 473 Page 185-2. Overload Protection: Trouble Light And Checking Shield Cup Shutdown SystemIf certain problems occur, thetrouble light comes on,

OM-194 473 Page 195-3. Torch And Work Cable ConnectionsIf torch or work cable needs to beremoved or replaced, proceed asfollows:Turn power Off, and di

OM-194 473 Page 205-4. Checking/Replacing Retaining Cup, Tip, And ElectrodeOvertightening will strip threads. Do not overtighten retaining cup duringa

OM-194 473 Page 215-5. Troubleshooting Power SourceConnect unit to proper inputvoltage. (see Section 3-8).YesNoIs input powerconnected tocorrect linev

OM-194 473 Page 225-6. Troubleshooting TorchTorch travel speed too slow;increase travel speed (seeSection 4-2). Clean orreplace torch consumablesas ne

OM-194 473 Page 23SECTION 6 – ELECTRICAL DIAGRAMFigure 5-1. Circuit Diagram For 120 Volts AC Power Source (Non-CE Models)202 707

OM-194 473 Page 24202 701Figure 5-2. Circuit Diagram For 230 Volts AC Power Source (CE Models)

OM-194 473 Page 25Notes

TABLE OF CONTENTSSECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1. . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1. . . .

OM-194 473 Page 26SECTION 7 – PARTS LISTFigure 6-1. Main Assembly. Hardware is common andnot available unless listed.802 462-D245678910111213141516192

OM-194 473 Page 27DescriptionPartNo.ItemNo.Figure 6-1. Main AssemblyQuantityDia.Mkgs.1 +206 302 WRAPPER 1. . . . . . . . . . . . . . . . . . . . .

OM-194 473 Page 281 183 427 Handle Assy, left and right w/screws (1)2 171 248 Pushbutton Switch (1)3 196 931 Leads, 20ft (1)4 196 930 Label, ICE-12C (

Notes

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 6/02Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA  2003 Miller Electric Mfg. Co. 1/03Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 US

dec_con1_11/02Declaration of Conformity forEuropean Community (CE) ProductsThis information is provided for units with CE certification (see rating la

OM-194 473 Page 1SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USINGpom _nd_9/981-1. Symbol UsageMeans Warning! Watch Out! There are possible hazardsw

OM-194 473 Page 2D On inverter power sources, failed parts can ex-plode or cause other parts to explode whenpower is applied. Always wear a face shiel

OM-194 473 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can cause severe burns.D Do not touch hot parts bare ha

OM-194 473 Page 41-4. Principal Safety StandardsSafety in Welding and Cutting, ANSI Standard Z49.1, from AmericanWelding Society, 550 N.W. LeJeune Rd,

OM-194 473 Page 5SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT UTILISATIONpom_nd_fre_5/971-1. Signification des symbolesSignifie Mise en garde ! Soy