Miller Electric 125C Owner's Manual

Spectrum 125CAnd ICE-12C TorchProcessesDescriptionRAir Plasma Cuttingand GougingAir Plasma CutterOM-2248 213 990G2010−07File: Plasma CuttersVisit our

OM-2248 Page 2D Assurez−vous que le fil de terre du cordon d’alimentation est cor-rectement relié à la borne de terre dans la boîte de coupure ou quel

OM-2248 Page 3D Ne coupez pas dans un endroit près d’opérations de décapage, denettoyage ou de vaporisation. La chaleur et les rayons d’arc peu-vent r

OM-2248 Page 4Les CHAMPS ÉLECTROMAGNÉTIQUES (CEM)peuvent affecter les implants médicaux.D Les porteurs de stimulateurs cardiaqueset autres implants mé

OM-2248 Page 52-4. Proposition californienne 65 AvertissementsLes équipements de soudage et de coupage produisent desfumées et des gaz qui contiennent

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 6SECTION 3 − DEFINITIONS3-1. Symbols And Definitions For Nameplate And Serial

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 7SECTION 4 − INSTALLATION4-1. SpecificationsPrimaryVoltsPrimaryAmperesPrimary

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 84-4. Serial Number And Rating Label LocationThe serial number and rating info

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 94-6. Torch Dimensions And WeightRef. 801 397-A3.0 lb (1.4 kg)1 in.(25 mm)8-3

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 104-10. Connecting Input PowerRef. 802 460-BCheck input voltage available atsi

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 11SECTION 5 − OPERATION5-1. Controls2Ref. 245 701-A11 Power SwitchThe cooling

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 125-2. Cutting SpeedThe cutting speed curve shows therecommended maximum cutti

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 13out bottom of cut.801 400-A5-4. Sequence Of OperationAfter cutting arc start

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 14SECTION 6 − MAINTENANCE & TROUBLESHOOTING6-1. Routine Maintenance! Disco

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 156-2. Overload Protection: Trouble Light And Checking Shield Cup Shutdown Sys

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 166-3. Torch And Work Cable ConnectionsIf torch or work cable needs to beremov

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 176-4. Checking/Replacing Retaining Cup, Tip, And Electrode! Overtightening wi

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 186-5. Compressor Filter Cleaning And Replacement! Turn Off power source, andd

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 196-6. Troubleshooting Power SourceConnect unit to proper inputvoltage. (see S

. A complete Parts List is available at www.MillerWelds.comOM-2248 Page 206-7. Troubleshooting TorchTorch travel speed too slow;increase travel speed

OM-2248 Page 21SECTION 7 − ELECTRICAL DIAGRAM245 705-AFigure 7-1. Circuit Diagram

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1...1-1. Symbol Usage 1...

OM-2248 Page 22SECTION 8 − PARTS LIST8-1. Recommended Spare PartsDescriptionPartNo.ItemNo.Recommended Spare PartsQuantityDia.Mkgs.245 728 KIT, ICE-12C

OM-2248 Page 231 183 427 Handle Assy, left and right w/screws (1)2 171 248 Pushbutton Switch (1)3 248 174 Leads, 20ft (1)4 196 930 Label, ICE-12C (1)5

TM-188 304 Page 24Invision 354MPNotes16 Gauge (.063 in.)22 Gauge (.031 in.)24 Gauge (.025 in.)20 Gauge (.037 in.)18 Gauge (.050 in.)14 Gauge (.078 in.

NotesWork like a Pro!Pros weld and cutsafely. Read thesafety rules atthe beginningof this manual.

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 2010−01Your distributor also givesyou ...ServiceYou always get the

ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2010 Miller Electric Mfg. Co. 2010−01Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer

OM-2248 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGpom_2010−03Protect yourself and others from injury — read and follow these precaution

OM-2248 Page 2SIGNIFICANT DC VOLTAGE exists ininverter power sources AFTER the re-moval of input power.D Turn Off unit, disconnect input power, check

OM-2248 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceHOT PARTS can burn.D Do not touch hot parts bare handed.D Allow cool

OM-2248 Page 41-4. California Proposition 65 WarningsWelding or cutting equipment produces fumes or gaseswhich contain chemicals known to the State of

OM-2248 Page 1SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANTUTILISATIONpom_2010−04freSe protéger et protéger les autres contre le risque de blessure